[remfini]

Ok I found the ones on the rear sway bar. So I found 5 in total. Thanks!

 

[camo man]

I've got the 2017 hunter edition. I have the updated drive shaft. I can only find 1 on the middle of the drive shaft accessible through the floor panel on inside. Than 2 on the front sway bar mount. That's it???

 

[Johnny 7]

Should be 2 on the rear sway bar also if i remember correctly.

 

[camo man]

Nope. Not there. I checked again today. I have only the three.

 

[waxjob]

The ones on the rear sway bar are hardly visible as they are on the front side of the frame where they are mounted.

Sent from my SM-G930W8 using Tapatalk

 

[camo man]

Sorry for doubting you guys. Found the ones on the front and rear sway bars also the one on the rear drive spline and the middle. That is 6 total. Thanks you guys!!!

 

[Roadrunner]

I recently removed my skid plate and lo and behold I found two more grease fittings on the drive shafts between the two pillow block bearings. Very difficult to find with the skid plate in place! Look for the two U Joints and you will find the two grease fittings in question!

 

[Rake1]

my 2020 general has four that I can find 2 front swaybar and two on driveshaft

 

[Cataholic]

Hello guys, I am having trouble finding any grease zerks on my 2020 Polaris ranger 1000 eps. I know this isn't the ranger forum as I have had no luck on that forum. I am new to side by sides and not very mechanical. I have read the whole owners manual and cannot find anything about grease zerks. Any help would be appreciated.

 

[Corbo1962]

Hello guys, I am having trouble finding any grease zerks on my 2020 Polaris ranger 1000 eps. I know this isn't the ranger forum as I have had no luck on that forum. I am new to side by sides and not very mechanical. I have read the whole owners manual and cannot find anything about grease zerks. Any help would be appreciated.

I don't know much about the rangers, but maybe they are similar in their methodology. So I would read the thread above and watch this guys video and maybe it'll put you on the right track. Hope this helps!

 

[GrandGrendel58]

my 2020 general has four that I can find 2 front swaybar and two on driveshaft

Where in the world are the two front sway bar zerks on the 2020? I felt all around the mounting bushing and did not feel any. If you dont mind taking a picture of where they are I would greatly appreciate it. I am doing my 50Hr/500Mile maintenance right now and they seem to be eluding me the most out of everything.


Also if someone knows how in the world I am supposed to "lubricate" the steering that would be very helpful as well. I am not seeing any zerks on the steering shaft/u-joints, as well as what to use and what to lube in regards to "General Lubrication: Lubricate all fittings, pivots, cables, etc." as per the service manual?

 

[Buelligan666]

2020 XP4 here, no front zerks. Seems they removed them, much like most people do with their front sway bar. I'm going to be removing mine.

 

[GrandGrendel58]

2020 XP4 here, no front zerks. Seems they removed them, much like most people do with their front sway bar. I'm going to be removing mine.

I had assumed there were none, but had to confirm I may eventually remove my front sway bar, but out here we can drive them on the road, so I am not sure I want to loose the stability on the hard stuff (especially since I dont have a trailer and "drive" my machine to every trail that is not directly accessible from my house).

 

[Rake1]

My 2020 G2 premium still has them in the front